A skylight lets in more heat than almost any other window in your house, because the roof faces the sun all day. The most direct fix for an existing skylight is solar control window film, which cuts the sun's heat at the glass and keeps the light. We install it on-site in Volusia and Flagler counties through our residential window tint service. The rest of this guide explains why skylights run hot, how each fix compares, and what to check before you choose.
TL;DR
- Skylights admit three to four times the solar cooling load of a window of the same orientation, except north-facing ones, so the heat is physics, not a defect in your home.
- The number that matters is the solar heat gain coefficient (SHGC): the lower it is, the less of the sun's heat gets in.
- Treating the glass itself, with solar control film or better glazing, stops heat before it enters the room. Interior shades only manage heat after it has passed through.
- Florida's guidance for existing skylights is to add window tint or a remote-control shade.
- Film also helps with UV and glare, which matters for floors, furniture and the comfort of the room.
Table of Contents
- Why a skylight makes a room so hot
- The two numbers on every glass label
- Your options, from the glass outward
- How the options compare
- What about UV and fading?
- What to check before you treat a skylight
- Is the skylight worth the energy trade-off?
- Promo: tinting the glass at your home
- Our view on skylight heat
- FAQ
- Sources
Why a skylight makes a room so hot
Think about where the sun sits for most of a Florida day: high overhead. A wall window sees that sun at a steep angle and a roof opening looks straight at it. The Pacific Northwest National Laboratory's guide notes that the roof receives sunlight all day, and it advises minimizing skylight area and choosing low-SHGC glazing.
A federal laboratory study of skylight solar gain, published through the Department of Energy's OSTI archive, put numbers on it. Solar cooling loads for skylights were three to four times those of windows with the same orientation, whatever the tilt, with north-facing units the exception. South-facing skylights peaked at a tilt of roughly 20 degrees, which is close to the pitch of many low-slope roofs.
Three things decide how much heat reaches your room:
- Glass type. Clear single glazing passes the most heat. Tinted, low-emissivity (low-e) or film-treated glass passes less.
- Size and location. HUD's consumer guide says skylight size typically should not exceed 5 to 15 percent of the room's floor area, depending on how many windows the room has. It also says location and roof slope affect both daylight and solar heat gain.
- Orientation. South- and west-facing skylights take the worst of an afternoon in Volusia County.
The two numbers on every glass label
HUD explains the two ratings you will see. The U-factor is the rate of non-solar heat conduction, and lower is better. SHGC is the fraction of solar radiation that is admitted and released as heat inside, and a lower number blocks more summer heat.
In Florida, SHGC is the one to watch, since the problem is the sun and not the cold. For new purchases, Florida's home energy program points to ENERGY STAR skylights for the southern zone with an SHGC of 0.28 or lower and a U-factor of 0.60 or less. The state's 9th edition (2026) energy code changes also set a maximum skylight SHGC of 0.28 for climate zones 1 and 2, down from 0.30. That tells you how much weight Florida puts on skylight heat.
If your skylight is older, it probably sits well above that. A new unit is a big project. Treating the glass you already have is a smaller one.
Your options, from the glass outward
There are four ways to cut skylight heat. They work at different points on the sun's path: outside the glass, in the glass, on the glass or inside the room.

1. Solar control film on the glass
Film goes on the interior surface of the skylight and reduces how much solar energy passes through. The glass stays in place, the light still comes in, and the work takes hours rather than days. The Florida home energy program names window tint as a fix for skylights that let heat in. HUD lists heat-absorbing tints among the glazing options for cutting unwanted summer solar heat gain. The Rutgers NJ Green Building Manual includes low-e coatings and films, and climate-appropriate window tinting in its list of window and skylight upgrades.
Our Solar Control Films are made for exactly this job on homes and buildings: reducing heat, UV and glare at the glass.
2. Better glazing when you replace the unit
New skylights can be ordered with low-e coatings, insulated glazing and gas fills. The EPA's ENERGY STAR materials say that qualified windows and skylights can block 70 percent or more of solar heat gain in summer, and that their performance is independently tested and certified by the National Fenestration Rating Council (NFRC), the body that issues the ratings on the label.
Replacement makes sense when a skylight leaks, fogs between the panes or is at the end of its life. If the unit is sound, treating the glass gets you much of the benefit without opening the roof.
3. Exterior shading
Screens, awnings and shade trees stop sunlight before it reaches the glass. The Department of Energy's study of window attachments modeled more than 16,000 runs across 12 U.S. climate zones. It found exterior attachments are generally more effective at saving cooling energy, and in cooling-dominated climates every attachment saves energy by lowering SHGC.
The trade-off on a roof is exposure. Anything mounted outside takes wind, rain and Florida UV, and it has to be fixed around flashing without creating a leak path. Many homeowners find that is a lot of roof work for one opening.

4. Interior shades and blinds
Shades are the familiar answer, and they do help. PNNL's guide recommends considering interior shading attachments on top of low-SHGC glazing. The catch is that sunlight has already passed through the glass by the time it hits the shade, so the heat is already in the room.
The same Department of Energy study found that results depend on use: the team stressed that the same operable shade can save or waste energy depending on how and when people use it. A shade that is open all afternoon does nothing. A skylight 12 feet up is not one you adjust twice a day. Film works whether or not anyone remembers to touch it.
The best setups combine layers: film or better glass to stop heat at the source, and a shade for the hours you want the room dark.
How the options compare
| Option | Where it stops heat | Daylight | Effort and upkeep |
|---|---|---|---|
| Solar control film | At the glass, before it enters the room | Keeps natural light, with less glare | One installation, no daily operation |
| New low-e skylight | In the glass | Keeps natural light | Roof work, best at re-roofing or end of life |
| Exterior shade or screen | Before the glass | Depends on the fabric | Weather exposure, roof-safe mounting |
| Interior shade or blind | After the glass | Blocks light when closed | Must be opened and closed on schedule |
What about UV and fading?
Heat is half of the story. The same sun that overheats the room fades floors, rugs and furniture. The EPA's ENERGY STAR materials state that low-e coatings can reduce fading of furnishings by up to 75 percent.
Many skylights already filter some UV. Units built with a laminated inner pane can block over 99 percent of UV-A and UV-B, according to one skylight manufacturer. Older acrylic domes and plain glass units vary a lot. Visible light still causes some fading, so UV control and heat control are best handled together at the glass. Our solar control films are designed to reduce heat, UV and glare in one step.
What to check before you treat a skylight
A few checks avoid most disappointments.
- Find the glass type. Single pane, double pane, laminated or acrylic dome each behave differently under film. Look for an etched label in a corner of the glass or the manufacturer's sticker on the frame.
- Note the orientation and how much of the room it lights. A large south or west-facing skylight over a living area is the strongest candidate.
- Check the warranty. Window and skylight warranties can be affected by what is applied to the glass, so read yours before any work.
- Decide what you want from the light. Film lowers glare and heat while keeping the room bright. A blackout shade is a different goal, for a bedroom, for example.
- Match the fix to the climate. HUD notes that climate determines the best ratings for skylights in each U.S. zone. In Daytona Beach or Palm Coast, cooling is the priority.
If you are not sure what glass you have, send us a photo and the room's location. We can tell you whether film is a good fit for it.
Is the skylight worth the energy trade-off?
Skylights are rarely put in to save energy. A Department of Energy study of commercial toplighting observes they are usually installed for aesthetic or programmatic reasons, and that with lighting controls they can save 35 to 55 percent of lighting energy. For homeowners, the value is daylight and the feel of the room. You keep that value by controlling the heat at the glass, not by covering the skylight and giving up the light.
Promo: tinting the glass at your home
We bring the work to you. Our Solar Control Films and Residential Window Tint services are performed at your property by our mobile team, so you do not need to take a day off or move anything. We serve Daytona Beach, Deltona, DeLand, New Smyrna Beach, Port Orange, Ormond Beach, Palm Coast, Edgewater and the surrounding area.

If you also want the rest of the house, or your car, treated, we can plan it in one visit. Our commercial window tint service covers offices and storefronts with glare and heat problems, and the automotive page covers cars. Our ceramic tint installation guide shows what a careful install looks like.
Our view on skylight heat
Most people call us about the skylight last. They have already tried the shade, and the room is still hot at 3 p.m.
Our view is simple: heat is cheapest to stop where it comes in. That is why we focus on ceramic-only premium film, careful prep and fitment, and installation at your home without rushing the job. Our formula is designed to cut heat, UV and glare while the room stays bright.
Our work comes with a comprehensive warranty that includes no-fault coverage, and our mobile units arrive fully equipped, so the job is done where the problem is.
Tint
FAQ
Does window film work on a skylight?
Yes. Florida's home energy guidance names window tint among the ways to reduce heat from an existing skylight. The right film depends on the glass type and the room, which is why we look at the skylight before we recommend one.
What is the best way to reduce heat from a skylight in Florida?
Stop the sun at the glass. Solar control film on an existing skylight, or a low-SHGC unit when you replace it, keeps heat out of the room. Shades can be added for darkness, but they work after the heat has entered.
Are skylights UV blocking?
It depends on the glazing. Laminated inner panes can block over 99 percent of UV, while older glass and acrylic units vary. Low-e coatings also cut fading of furnishings, according to the EPA's ENERGY STAR materials.
Will film help my AC bill?
By lowering the solar heat entering the room, film reduces the load on your air conditioner. Savings depend on your skylight size, orientation and home. Federal research shows that cutting solar heat gain through windows lowers cooling energy in hot climates.
Sources
- Evaluation of solar gain through skylights (OSTI, 1993)
- Shading and Solar Control for Windows and Skylights (PNNL)
- HUD PATH: Resource- and Energy-Efficient Fixtures
- Windows and Skylights (Florida Home Energy)
- Analysis of Changes for the 9th Edition (2026) Florida Codes
- EPA: ENERGY STAR Qualified Windows
- NJ Green Building Manual: Window and Skylight Upgrades
- Energy Savings from Window Attachments (DOE)
- Commercial Building Toplighting (DOE)
- UV Protection for Skylights
